Huffy Universal Elevator Mount Owner'S Manual Download Page 11

11

10/01

P/N 211125A

Item #5 (2)

HARDWARE IDENTIFIER

PARTS LIST 

*  

YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.

Item #4 (2)

Item Qty.

Part No.

Description

1

1

206117

Label, Warning

2

1

906377

U-Channel

3

2

906206

Struts

4

2

202662

Bolt, Hex Head 5/16-18 x 4-1/2

5

2

203099

Nut, Lock 5/16-18

6

1

906350

Bracket, Angled, Left 

7

1

906349

Bracket, Angled, Right

8

2

900846

Board Bracket, (Black)

9

1

201122

Bolt, Hex Head, 3/8-16 x 3-1/4 Long

10

2

201133

Support Bracket

11

2

201129

Spacer, 1-3/4 Long

12

1

201126

Release Lever

13

1

800878

Pawl & Pin Assembly 

14

1

201124

Locknut, Hex Head, 3/8-16

Item Qty.

Part No.

Description

15

1

240017

Bolt, Hex Head, 1/4-20 x 2-1/4 Long

16

1

203493

Locknut, Hex Head 1/4-20

17

4

904807

Elevator Tube, (Black)

18

5

201640

Bolt, Hex Head, 1/2-13 x 7-1/4 Long

19

4

201642

Spacer, Plastic

20

1

201140

Wave Washer

21

1

201156

Ratchet

22

6

206340

Locknut, Hex Head, 1/2-13

23

1

201125

Spring

24

2

900866

Bracket, Pole

25

2

203437

U-Bolt, 3/8-16 x 4-1/2

26

2

202675

Clamp, Saddle

27

4*

203309

Washer 13/32 x 1

28

4*

203017

Hex Nut, 3/8-16 

Item #9 (1)

Item #14 (1)

Item #15 (1)

Item #16 (1)

Item #19 (4)

Item #20 (1)

Item #22 (6)

Item #27 (4)*

Item #28 (4)*

Summary of Contents for Universal Elevator Mount












Reviews: