WARNING!
Fixtures must be grounded and installed in accordance with the National Electrical Code and all local codes. Failure to do so may increase the
RISK OF PERSONAL
INJURY, PROPERTY DAMAGE, FIRE AND DEATH.
Install and use so fixture failures do not cause a hazard and use only in environments for which the product is specifically
marked.
WARNING!
This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other reproductive harm. Thoroughly wash hands after
installing, handling, cleaning, or otherwise touching this product.
CAUTION!
Follow ALL luminaire recommendations, product markings, instructions, restrictions and warnings regarding lumninaire operation and burning position. Luminaire label
shows electrical and environmental requirements and restrictions.
All electrical work must be done by a qualified electrician.
Turn off electric power to all affected circuits and allow to cool before servicing.
A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally
sufficient for the optical system. Any accumulation of dust or dirt should be removed regularly.
Carefully read these instructions before installing product. If you do not understand these instructions, before starting any work, contact your Hubbell Lighting distributor or
[email protected] or (864) 678-1000
Give instructions to facility owner/manager for future reference.
INSTALLATION INSTRUCTIONS - WGH81L
SAVE THESE INSTRUCTIONS
TOOLS REQUIRED: (NOT INCLUDED) ANY TOOLS NEEDED FOR APPROPRIATE WALL FASTENERS, PHILIPS HEAD SCREW DRIVER, PLIERS
PARTS REQUIRED: (NOT INCLUDED) SILICONE CAULK, WALL ANCHORS AND FASTENERS APPROPRIATE FOR WALL CONSTRUCTION TYPE
FIXTURE MOUNTING WITH JUNCTION BOX
1. ATTACH MOUNTING PLATE (ITEM 1) TO RECESSED JUNCTION BOX (ITEM 2) USING APPROPRIATE HARDWARE
(SUPPLIED BY OTHERS.)
WARNING! INSTALLER IS RESPONSIBLE FOR ENSURING THE FIXTURE IS PROPERLY
ATTACHED AND SEALED TO THE JUNCTION BOX. DEPENDING ON THE WALL TEXTURE AND INSTALLATION
JUNCTION BOX, CAULK MAY NEED TO BE APPLIED TO PREVENT WATER FROM GETTING INTO JUNCTION BOX.
2. PULL WIRES THROUGH GASKET AND MOUNTING PLATE.
3. LOOSEN THE FOUR SCREWS (ITEM 3) LOCATED AT THE CORNERS OF THE LENS AND THEN ROTATE THE LENS
ASSEMBLY (ITEM 4) DOWNWARD. TAKE CAUTION NOT TO DROP LENS ASSEMBLY ONCE SCREWS ARE REMOVED.
4. LOOSEN AND REMOVE THE FOUR HEAT SINK SCREWS (ITEM 5) AND THEN REMOVE THE HEAT SINK (ITEM 6).
5. MOUNT THE FIXTURE SO THAT THE THREADED MOUNTING BOSS (ITEM 7) COMES THROUGH THE BACK OF THE
HOUSING AND THEN TIGHTEN PROVIDED NUT SECURELY (ITEM 8) ON THE THREADED MOUNTING BOSS.
6. WIRE SERVICE LEADS TO FIXTURE POWER LEADS ACCORDING TO LOCAL AND NATIONAL ELECTRICAL
CODES. CONNECT GROUND WIRE TO GREEN WIRE. CONNECT BLACK TO BLACK AND WHITE TO NEUTRAL
THEN PUSH CONNECTIONS BACK INSIDE THE JUNCTION BOX (ITEM 2)
.
7. PLACE HEAT SINK (ITEM 6) BACK IN THE HOUSING THEN RE-INSERT AND TIGHTEN THE HEAT SINK SCREWS
(ITEM 5).
8. CLOSE LENS ASSEMBLY (ITEM 4) AND TIGHTEN THE LENS ASSEMBLY SCREWS (ITEM 3).
FIXTURE MOUNTING WITH CONDUIT
1. SECURE MOUNTING PLATE (ITEM 1) TO A JUNCTION BOX OR WALL USING APROPRIATE HARDWARE.
WARNING! INSTALLER IS RESPONSIBLE FOR ENSURING THE FIXTURE IS PROPERLY ATTACHED AND
SEALED TO THE JUNCTION BOX. DEPENDING ON THE WALL TEXTURE AND INSTALLATION JUNCTION
BOX, CAULK MAY NEED TO BE APPLIED TO PREVENT WATER FROM GETTING INTO JUNCTION BOX.
2. MOUNT THE REAR HOUSING (ITEM 9) TO THE JUNCTION BOX BY FOLLOWING THE SAME STEPS
LISTED FOR "MOUNTING FIXTURE TO JUNCTION BOX".
3. LOOSEN AND REMOVE DESIRED CONDUIT PLUGS (ITEM 10) AND CONNECT FIXTURE LEADS TO
SUPPLY LEADS WITH WIRE NUTS.
4. CLOSE LENS ASSEMBLY (ITEM 4) AND TIGHTEN THE LENS ASSEMBLY SCREWS (ITEM 3).
MOUNTING NOTE: IF JUNCTION BOX IS NOT USED, IT IS RECOMMENDED THAT THE MOUNTING PLATE IS
ATTACHED TO A NON-COMBUSTABLE MOUNTING SURFACE. AVOID DRILLING CLOSE TO LIVE WIRES AND
MAKE SURE THAT THERE IS AT LEAST 1/2" CLEARANCE. THIS FIXTURE IS INTENDED FOR MOUNTING ON
WEATHERPROOF JUNCTION BOX WITH PROVIDED GASKET. AFTER INSTALLATION, USE SILICONE
SEALANT TO CREATE A WEATHERPROOF SEAL BETWEEN THE MOUNTING SURFACE AND THE BASE OF
THE FIXTURE.
MOUNTING PLATE LAYOUT
3.43
1.94
2.48
4.22
ITEM 2
ITEM 1
ITEM 1
ITEM 3 4X
ITEM 4
ITEM 5 4X
ITEM 6
ITEM 7
ITEM 8
ITEM 9
ITEM 10
Hubbell Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2016 Hubbell Lighting, All Rights Reserved • For more information visit our website: www.hubbelloutdoor.com • Printed in USA
1.94
2.48
3.43
93073164 Rev. A