Hubbell GARD Pro Instruction Manual Download Page 128 | Manualshive

Page: 128 / 345

background image

System Configuration __________________________________________________________________

RF-MCGARDPRO

Hubbell Power Systems, Inc.

–

RFL™

Products

July 1, 2022

©2022 Hubbell Incorporated

4-53

Table 4-5. TSD Push Button Interface fields

Field

Description

Values

PB #

The number associated with the Push
Button.

1-8 read only

HMI IN BIT

Number of the HMI IN bit.

2-61

DESCRIPTION

Label provided by the user.

BUTTON TYPE

“Toggle” or “Pulse” depending on the needs
of the button. “Toggle” switches between
values on and off while “Pulse”
momentarily turns the switch on.

Pulse, Toggle

ENABLE

If enabled the switch Is present in the
display.

Enable, disable

“On” Text*

The text desired for the display of the “On”
value.

1-4 character string

“On” Color*

The color desired for the display of the “On”
value. The text is made black or white to
create the highest contrast.

Green, Silver, Black, White,
Red, Lime, Yellow, Blue

“On” Preview*

Preview of the appearance of the “On”
button showing the text and the color
chosen.

Display only

“Off” Text*

The text desired for the display of the “Off”
value.

1-4 character string

“Off” Color*

The color desired for the display of the
“Off” value. The text is made black or
white to create the highest contrast.

Green, Silver, Black, White,
Red, Lime, Yellow, Blue

“Off” Preview*

Preview of the appearance of the “Off”
button showing the text and the color
chosen.

Display only

If buttons are not enabled
on the configuration web
page they will not appear
here

Current state

has Black

border

Color set on the
configuration web page

Push Button Label Text
set on Advanced/TSD
Settings web page

A single button appears if button
type is set to pulse on the Push
Button Interface Configuration web
page.

When this “Pulse” button is

pressed and confirmed the HMI bit
will be set high and then low, acting
like a momentary push button.

OFF 0

Breaker 12

ON 1

ON 2

OFF2

Breaker 22

OFF 1

ON1

ON 4

ON 6

ON 3

OFF3

OFF4

ON 5

Reset

Mod 12

Mod 22

OFF5

OFF6

Description 5

Description 6

Description 7

Description 8

Figure 4-50. TSD Push Button Interface.

«
...
126
127
128
129
130
...
»

Summary of Contents for GARD Pro


























































































































































































































































































































































Reviews:

No comments

Related manuals for GARD Pro

Brand: NetComm Pages: 2

Brand: Giacomini Pages: 2

Brand: HEIDENHAIN Pages: 28

Brand: ESI Pages: 3

Brand: GLI Pages: 4

Brand: Samcon Pages: 12

Brand: ExtenHD Pages: 4

Brand: CommScope Pages: 2

Brand: AKG Pages: 2

Brand: Konig Pages: 56

Brand: SeeEyes Pages: 16

Brand: VOLTCRAFT Pages: 2

Brand: Yaesu Pages: 8

Brand: US Conec Pages: 17

Brand: Thitronik Pages: 6

Brand: CYP Pages: 16

SOLARLOK 4-1394462-6

Brand: Tyco Electronics Pages: 6

SafeLok Anchorage 4011

Brand: 3M Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands