Hubbell GAI-TRONICS Page/Party 780-301 Manual Download Page 13

Pub.  42004-638L2 

Model 780/7805-301 Page/Party

®

 Handset Stations for Cenelec Zone 1 Applications 

Page: 13 of 15 

\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-638l2.doc 
6/98 

Troubleshooting 

The table below describes possible solutions for some common problems. 

Problem Solution 

Speaker level requires 
adjustment. 

Adjust the Speaker Volume Control, labeled 

USER

 

ADJ

, at the 

amplifier. 

Outgoing conversation level 
requires adjustment. 

Adjust Microphone Gain at the amplifier. 

Incoming conversation level 
requires adjustment. 

Adjust the Receiver Volume Control at the amplifier. 

Feedback/distortion (a hum or 
buzz on the line) occurs during 
all Page/Party

®

 station operation. 

1.

 

Adjust the Receiver Volume Control at the amplifier. 

2.

 

The line may be improperly terminated.  Inspect the system cable 
for loose connections, shorts, and grounds.  Line balance 
assembly connections are critical. 

Sidetone* requires adjustment. 

*Hearing one’s own voice in the 
receiver of the handset. 

1.

 

Adjust the Receiver Sidetone at the amplifier. 

2.

 

Check that the system cable connections to the resistors in the 
line balance assembly are properly connected to the line balance 
assembly resistors. 

Crosstalk occurs. 

One or more system cable pairs may be improperly terminated.  
Visually inspect the system cable connections for accidental crossing 
of the cable pairs or grounds. 

Feedback during page of nearby 
handset station. 

Use the muting feature in the amplifier enclosure at the terminal 
blocks. 

 

Summary of Contents for GAI-TRONICS Page/Party 780-301

















Reviews: