manualshive.com logo in svg

Hubbell GAI-Tronics 10370-701, Manual, Page: 10 / 16

Share
Download
Hubbell GAI-Tronics 10370-701 Manual Download Page 10

Pub. 42004-463C 

VoIP Speaker Amplifier Interface 

Page 8 of 13 

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-463C.docx 

03/20 

Power 

Ground 

The unit must be connected to earth ground: 

1.

 

Install a #6 ring lug on the incoming ground wire. 

2.

 

Secure the ground conductor to the ground stud, located in the upper right corner of the housing. 

PoE (Power over Ethernet) 

The device can be powered from the network cable if the speaker output requirement is less than 8 watts.  
PoE works across standard network cabling (i.e. Cat5) to supply power directly from the data ports where 
the device is connected. 

Connect the LAN cable (Category 5 or better UTP cable) to the RJ45 jack, located on the underside of the 
VoIP interface PCBA (see Figure 4). 

Local Power 

The device requires a 120/240 V ac  power source if the speaker output requirement is greater than 8 
watts. 

1.

 

Install spade lugs on the power line conductors. 

2.

 

Connect the power conductors to terminal block 

TB101

, located in the upper right corner of the 

housing (see Figure 4). 

 

Figure 4.  Field Wiring Connections 

Summary of Contents for GAI-Tronics 10370-701

















Reviews:

No comments