manualshive.com logo in svg

Huawei V100R006C00, Configuration Manual

Share
Download
Huawei V100R006C00 Configuration Manual Download Page 41

3.4 Typical Topology of a Stack

This section describes two typical topologies of a stack.

Ring Topology

The typical topology of a stack is a ring topology. As shown in 

Figure 3-3

, stack interfaces on

the Switches are connected through leased stack cables.

NOTE

Do not directly connect stack ports on the same switch to form a loop.

Figure 3-3

 Ring Topology

stack link

common link

SwitchA

SwitchC

SwitchD

SwitchB

 

Link Topology

As shown in 

Figure 3-4

, stack interfaces on the Switches are connected through leased stack

cables.

NOTE

Do not directly connect stack ports on the same switch to form a loop.

Figure 3-4

 link Topology

SwitchA

SwitchB

SwitchC

PC1

PC2

stack link

common link

Quidway S5700 Series Ethernet Switches
Configuration Guide - Device Management

3 Stacking

Issue 01 (2011-07-15)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

32

Summary of Contents for V100R006C00















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands