Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 61 / 138

Step 4 Remove packing materials, as shown in

Figure 3-4

Figure 3-4 Removing packing materials

Step 5 Remove the plastic bag and take out the fittings box.
Step 6 Check that the UPS is intact.

1. Visually inspect the UPS appearance for shipping damage. If it is damaged,

notify the carrier immediately.

2. Check that the equipment and fittings are correct and complete according to

the packing list. If some fittings are missing or do not comply with the

packing list, record this information and contact the Company immediately.

Step 7 After confirming that the UPS is intact, remove the front and rear L-shaped

brackets that secure the UPS to the pallet, and secure the sliding plate to the

pallet using the two M12 bolts removed before.

Figure 3-5 Removing the L-shaped brackets

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

3 Installation

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands