Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 34 / 138

2.3.3 Bypass Module

Appearance

Figure 2-10 Bypass module

(1) Positioning lock

(2) Cold start button

(3) Running indicator (4) Alarm indicator

(5) Fault indicator

(6) Ready switch

(7) Signal port

(8) Input and output

ports

Table 2-3 Indicator description

Indicator

Color

Status

Description

Running

indicator

Green

Steady

The system is working in bypass mode.

Blinking

at long

interval

The bypass has no output (blinking at 0.2 Hz,

on for 2.5s and off for 2.5s).

Blinking

at short

interval

The bypass is not configured or the DSP

software is being upgraded (blinking at 4 Hz,

on for 0.125s and off for 0.125s).

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

2 Overview

Issue 03 (2022-01-30)

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands