Huawei UPS5000-E-120kVA-FM User Manual Download

Page: 129 / 138

7.3 Environmental Specifications

Item

Specifications

Operating

temperature

0°C to 40°C

Storage

temperature

–40°C to +70°C

Humidity

0–95% RH (non-condensing)

Altitude

0–1000 m
When the altitude is higher than 1000 m, the power is

derated as described in IEC 62040-3. The upper limit of the

altitude is 4000 m.

7.4 Safety and EMC

Item

Specifications

Safety

regulations

EN 62040-1

IEC 62040-1

TLC

YD/T 2165-2010

EMC

Conducted emission

EN/IEC 62040-2

Radiated emission (RE)

EN/IEC 62040-2

Low-frequency signal

interference

IEC 61000-2-2

Electrostatic discharge

immunity

IEC 61000-4-2

Conducted susceptibility

EN/IEC 62040-2
EN/IEC 61000-4-6

Radiated susceptibility

EN/IEC 62040-2
EN/IEC 61000-4-3

Electrical fast transient

(EFT)

EN/IEC 62040-2
IEC 61000-4-4

Surge protection

EN/IEC 62040-2
IEC 61000-4-5

Power frequency magnetic

field

IEC 61000-4-8

UPS5000-E-(30 kVA–120 kVA)-FM

User Manual

7 Technical Specifications

Issue 03 (2022-01-30)

121

Summary of Contents for UPS5000-E-120kVA-FM











































































































































Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands

Huawei UPS5000-E-120kVA-FM, User Manual

Search results

Summary of Contents for UPS5000-E-120kVA-FM

Reviews:

Related manuals for UPS5000-E-120kVA-FM

Brands by name

Popular brands