Huawei U8655N Maintenance Manual Download Page 14 | Manualshive

Page: 14 / 72

background image

U8655
Maintenance Manual

5 Software Upgrade

Issue 1.0 (2012-02-23)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

9

8.

After the upgrade is completed, the phone restarts and the NV items are restored.

9.

After the main upgrade pack is upgraded, upgrade the vendor upgrade pack using the
same upgrade method.

If the phone cannot be properly powered on, use one of the following two methods to forcibly
upgrade the phone:



Install the battery on the phone (if the screen is jittering, remove the battery and wait for
five seconds before installing the battery again). Press and hold the and
Volume– keys, and press the Power key. The phone enters the SD forcible upgrade mode
in which the upgrade process is similar to the normal upgrade.



While the phone has no battery installed, press and hold the and Volume– keys,
and connect the charger to the phone.

The phone enters the SD forcible upgrade. This method is recommended. If the forcible
upgrade still fails, use another microSD card and try forcible upgrade again.

«
...
12
13
14
15
16
...
»

Summary of Contents for U8655N









































































Reviews:

No comments

Related manuals for U8655N

Brand: Collage Investments Pages: 34

Brand: Positron Pages: 84

Brand: Sony Ericsson Pages: 208

Brand: PCD Pages: 62

Brand: OfficeServ Pages: 63

Brand: bq Pages: 88

Brand: HTC Pages: 4

Brand: Stanley Pages: 4

Brand: Haier Pages: 34

Brand: Haier Pages: 39

Brand: Haier Pages: 32

Brand: Haier Pages: 35

Brand: Haier Pages: 36

Brand: Haier Pages: 49

Brand: Haier Pages: 32

Brand: Haier Pages: 33

Brand: Haier Pages: 38

Brand: Haier Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands