Huawei TP3206 Installation Manual Download Page 80

Page: 80 / 200

HUAWEI TP3206&TP3218&TP3218S Telepresence

Installation Guide

8 Installing the First Row of the Multi-Functional

Conference Table

Issue 05 (2014-08-01)

Huawei Proprietary and Confidential

Figure 8-18

Installing the left steel plate and frame assembly (D1)

Step 10

Fully tighten all screws in the steel plate and frame assemblies.

Step 11

Place the left and right tabletop displays in the corresponding installation locations, as shown

Figure 8-19

Figure 8-19

Placing the left and right tabletop displays

Step 12

Partially fasten screws in the left and right tabletop segments (D6 and D5). The installation

method is the same for the left and right tabletop segments. In the following procedure, the

left tabletop segment (D6) is installed.

Summary of Contents for TP3206









































































































































































































Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands

Huawei TP3206, Installation Manual

Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands