Huawei TP3206 Installation Manual Download Page 44

Page: 44 / 200

HUAWEI TP3206&TP3218&TP3218S Telepresence

Installation Guide

6 Installing the Rear Panel

Issue 05 (2014-08-01)

Huawei Proprietary and Confidential

Installing the Rear Panel

About This Chapter

This chapter describes how to install the rear panel.

6.1 Parts List

6.2 Installation Procedure

6.3 Installation Effect

6.1 Parts List

Before installing the rear panel, gather the parts listed in

Table 6-1

Table 6-1

Rear panel parts list

No.

Name

Quantity

Center rear panel segment (B1)

Leftmost rear panel segment (B2)

Rightmost rear panel segment (B3)

M6 x 16 screw

Several

6.2 Installation Procedure

Background

The rear panel is placed behind the racks before the racks are installed. Follow the procedure

in this section to install the rear panel.
During installation:

Summary of Contents for TP3206









































































































































































































Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands

Huawei TP3206, Installation Manual

Search results

Summary of Contents for TP3206

Reviews:

Related manuals for TP3206

Brands by name

Popular brands