Huawei TP3106 Commissioning Manual Download Page 17 | Manualshive

Page: 17 / 202

background image

2.5 Powering Devices On

After unpacking cartons, check whether any device is dead on arrival (D.O.A). If any D.O.A
device is found, immediately contact the relevant personnel.

describes the devices to be checked and the checking criteria.

Table 2-4

Checking for D.O.A devices

Device

Checking Criteria

HD display

The HD displays can be powered on correctly
and video sources can be switched without
artifacts.

Telepresence host

You can use the telepresence host's default IP
address to log in to its web interface and
configure its parameters.

Telepresence codec

Video from the telepresence codecs can be
transmitted to the HD displays, that is, the
home screens of the telepresence codecs can
be viewed on the HD displays.

Tabletop display

The tabletop displays can be opened and
closed using the tabletop display buttons.

Tri-lens camera

Video from the tri-lens camera can be
transmitted to the HD displays, that is, the
three channels of video captured by the tri-
lens camera can be viewed on the HD
displays.

Speaker system

The speaker systems play audio sources
properly.

Touch panel

You can operate the touch panel's user
interface (UI) properly.

Wireless router

You can use the wireless router's default IP
address to log in to its web interface and
configure its parameters.

Network switch

The network ports on the network switch can
communicate with each other.

2.6 Setting IP Addresses

Before installing the TP3106&TP3118S&TP3118, assign six internal IP addresses (for access
to the telepresence system's internal network) to:

HUAWEI TP3106&TP3118&TP3118S
Commissioning Guide

2 Deployment Preparation

Issue 01 (2015-02-12)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

9

«
...
15
16
17
18
19
...
»

Summary of Contents for TP3106











































































































































































































Reviews:

No comments

Related manuals for TP3106

Brand: Waterway Pages: 8

Brand: Nakamichi Pages: 11

Brand: Sena Pages: 16

MR Confon Starter f MKII+

Brand: Cambridge Research Systems Pages: 34

Listening System PLS-900

Brand: Listen Pages: 2

Brand: Audio System Pages: 2

Bell'O Digital BDSW-1650-BLK

Brand: Twin-Star International Pages: 20

Brand: Akai Pages: 6

NOVA Powerplus VP3466

Brand: Vicon Pages: 101

CommandPro 23 Series

Brand: Cattron Pages: 27

Brand: LG Pages: 26

Brand: LG Pages: 20

Brand: LG Pages: 70

Brand: LG Pages: 50

Brand: LG Pages: 56

V-NET PQCPC22A0

Brand: LG Pages: 125

Brand: LG Pages: 38

Brand: Bogen Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands