Huawei TP3106 Commissioning Manual Download Page 13

Page: 13 / 202

Task

Description

Remarks

Power devices on

Power the telepresence
devices on and check
whether they operate
properly.

Set IP addresses

Set IP addresses for relevant
devices.

Install devices

Install the telepresence
devices according to chapter.
"TP3106&TP3118s&TP311
8 install guide"

Place devices

Place the telepresence
devices according to

1.2

Direction Conventions

Connect devices

Connect the telepresence
devices in the specified order
using prepared cables.

Upgrade the system

Upgrade all relevant
telepresence devices.

Configure parameters

Configure parameters
according to chapter

Parameter Configuration

Configure video devices

Configure video devices
according to chapter

5 Video

Device Configuration

Verify the system

Verify the system according
to chapter

6 System

Verification

2.2 Tools List

To unpack and install the telepresence system, you need the tools listed in

Table 2-2

Tools list

Tool

Illustration

Specification
s

Description

Phillips screwdriver

Used for installing
mechanical parts.

HUAWEI TP3106&TP3118&TP3118S
Commissioning Guide

2 Deployment Preparation

Issue 01 (2015-02-12)

Huawei Proprietary and Confidential

Summary of Contents for TP3106











































































































































































































Search results

Summary of Contents for TP3106

Reviews:

Related manuals for TP3106

Brands by name

Popular brands

Huawei TP3106, Commissioning Manual

Search results

Summary of Contents for TP3106

Reviews:

Related manuals for TP3106

Brands by name

Popular brands