Huawei TE80 Administrator'S Manual Download Page 67

Page: 67 / 178

HUAWEI TE80 Videoconferencing Endpoint
Administrator Guide

5 Microphone and Speaker

Issue 02 (2014-03-30)

Huawei Proprietary and Confidential

Connecting the VPM220W to the Endpoint

TThe endpoint can be connected over a Wi-Fi network to a VPM220W for sound pickup.

Before connecting the VPM220W to the endpoint, you must enable the Wi-Fi hotspot and set
Wi-Fi parameters as follows:



Set

Identity authentication mode

WPA-PSK

WPA2-PSK



Enable DHCP and set

Start IP address

and

End IP address

For details, see

Setting Wi-Fi Hotspot Parameters

To connect the VPM220W to the endpoint:

Step 1

Press the power button at the bottom of the VPM220W to power it on.

The VPM220W automatically searches for an available Wi-Fi network.



If the VPM220W was once connected to the endpoint, the connection between these two
will automatically set up, so you can skip the following steps.



If you are using the VPM220W for the first time or moving it outside the connected
Wi-Fi network range, go to

Step 2

and

Step 3

Step 2

Hold and press the button on top of the VPM220W for at least 3 seconds.

A confirmation dialog box is displayed on the remote controlled UI.

Step 3

Select

The VPM220W then performs the Wi-Fi Protected Setup (WPS) Push Button Configuration
(PBC) authentication with the videoconferencing endpoint in order to obtain an IP address.

----End

5.1.3 Setting Audio Parameters

Before using your endpoint to join a conference, set the audio parameters to gain the best
possible audio experience.

Procedure

Step 1

Choose

Advanced

Settings

Audio

. Set the audio parameters described in

Table 5-7

Table 5-5

Audio input parameters

Parameter

Description

Setting

MIC 1

MIC 2 (available only
for the TE80)

Adjusts the microphone
volume at your site. When
you adjust this microphone
volume, the volume heard at
remote sites is adjusted
accordingly.

These parameters are selected
by default.

RCA L

RCA R

Adjusts the input volume of
the RCA port at your site.
When you adjust this input
volume, the volume heard at

These parameters are selected
by default.

Summary of Contents for TE80



















































































































































































Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands

Huawei TE80, Administrator'S Manual

Search results

Summary of Contents for TE80

Reviews:

Related manuals for TE80

Brands by name

Popular brands