Huawei TaiShan 200 Series User Manual Download Page 58

Page: 58 / 132

Figure 5-10 Installing the front and rear ends of a holding rail

2. Insert the positioning pins on the rear of the rail into the square holes in the

cabinet. See (3) in

Figure 5-10

3. Align the front with a square hole, and push the holding rail forward until it

snaps into place. See (4) in

Figure 5-10

4. Push the hook backwards so that its metal sheet touches the mounting bar.

See (5) in

Figure 5-10

5. (Optional) Install an M6 screw in the third square hole at the rear of the

holding rail to secure it. See (6) in

Figure 5-10

6. Install the other holding rail in the same way.

Step 2 Install the server.

1. Pull out the inner rails as far as they will go. See

Figure 5-11

TaiShan 200 Server

User Guide (Model 2280)

5 Install and Configure

Issue 04 (2020-01-16)

Summary of Contents for TaiShan 200 Series





































































































































Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands

Huawei TaiShan 200 Series, User Manual

Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands