Huawei TaiShan 200 23280 User Manual Download Page 33

Page: 33 / 191

Drive Activity

Indicator (Green

Indicator)

Drive Fault

Indicator (Yellow

Indicator)

Description

Steady on

A member drive in the RAID array is

faulty.

2.6.3 NVMe SSD Indicators

Figure 2-23

shows the NVMe SSD indicators.

Figure 2-23 NVMe SSD indicators

Table 2-11 NVMe SSD indicators

Drive Activity

Indicator

(Green

Indicator)

Drive Fault

Indicator

(Yellow

Indicator)

State Description

Off

The NVMe SSD cannot be detected or the

PCIe link is down.

Steady green

Off

The NVMe SSD is detected and working

properly.

Blinking green

(2 Hz)

Off

Data is being read from or written to the

NVMe SSD.

Off

Blinking yellow

(2 Hz)

The NVMe SSD is being located or hot-

swapped.

Off

Blinking yellow

at 0.5 Hz

The NVMe SSD completes the hot removal

process and is removable.

Steady green or

off

Steady yellow

The NVMe SSD is faulty.

2.7 Riser Cards and PCIe Slots

show riser

cards supported by I/O modules 1 and 2 in a 2280.
●

The riser card shown in

Figure 2-24

can be installed in I/O module 1 or 2. It

provides PCIe slots 1 to 3 when installed in I/O module 1 and PCIe slots 4 to 6

when installed in I/O module 2.

TaiShan 200 Server (Model 2280)

User Guide

2 Components

Issue 09 (2021-01-12)

Summary of Contents for TaiShan 200 23280
































































































































































































Search results

Summary of Contents for TaiShan 200 23280

Reviews:

Related manuals for TaiShan 200 23280

Brands by name

Popular brands

Huawei TaiShan 200 23280, User Manual

Search results

Summary of Contents for TaiShan 200 23280

Reviews:

Related manuals for TaiShan 200 23280

Brands by name

Popular brands