Huawei SUN2000-60KTL-M0 User Manual Download Page 58

Page: 58 / 127

Figure 5-19 Communication mode for a single SUN2000

●

Figure 5-20

shows the communication mode for multiple SUN2000s.

If multiple SUN2000s are used, connect all the SUN2000s in daisy chain mode

over an RS485 communications cable.

Figure 5-20 Communication mode for multiple SUN2000s

NO TE

● The RS485 communication distance between the SUN2000 at the end of the daisy

chain and the SmartLogger cannot exceed 1000 meters.

● If multiple SUN2000s need to communicate with one another and are connected

to a PC over the SmartLogger1000, a maximum of three daisy chains can be

configured.

● If multiple SUN2000s need to communicate with one another and are connected

to a PC over the SmartLogger2000, a maximum of six daisy chains can be

configured.

● To ensure the system response speed, it is recommended that the number of

devices on each daisy chain be less than 30.

MBUS (PLC) Communication

The MBUS (PLC) communication board loads communication signals onto power

cables for transmission.

NO TE

The built-in MBUS (PLC) module in the SUN2000 does not need to be connected with

additional cables.

Selecting a Communication Mode

The RS485 and MBUS (PLC) communication modes are mutually exclusive.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

5 Electrical Connections

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands