Huawei SUN2000-60KTL-M0 User Manual Download Page 45

Page: 45 / 127

5.3 Opening the Maintenance Compartment Door

Precautions

CA UTION

● Never open the host panel cover of the SUN2000.
● Before opening the maintenance compartment door, ensure that neither of the

AC and DC connections to the SUN2000 is connected.

● Do not open the maintenance compartment door in rainy or snowy days. If

unavoidable, take protective measures to prevent rain or snow from entering

the maintenance compartment.

● Do not leave extra hardware in the maintenance compartment.

Procedure

Step 1 Partially loosen the two screws on the maintenance compartment door.

Figure 5-3 Loosening screws

NO TE

If the screws on the enclosure door are lost, obtain spare screws from the fitting bag bound

to the inductor cover at the bottom of the enclosure.

SUN2000-(60KTL, 65KTL)-M0

User Manual (Mexico Edition)

5 Electrical Connections

Issue 06 (2020-10-12)

Summary of Contents for SUN2000-60KTL-M0
































































































































Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands

Huawei SUN2000-60KTL-M0, User Manual

Search results

Summary of Contents for SUN2000-60KTL-M0

Reviews:

Related manuals for SUN2000-60KTL-M0

Brands by name

Popular brands