Huawei SUN2000-2KTL-L1 User Manual Download

Page: 45 / 122

●

WLAN-FE Smart Dongle (FE Communication)
You are advised to use a CAT 5E outdoor shielded network cable (outer

diameter < 9 mm; internal resistance ≤ 1.5 ohms/10 m) and shielded RJ45

connectors.

Figure 5-5 Installing a WLAN-FE Smart Dongle (FE communication)

NO TE

There are two types of Smart Dongle:
● For details about how to use the WLAN-FE Smart Dongle SDongleA-05, see the

SDongleA-05 Quick Guide (WLAN-FE)

. You can also scan the QR code to obtain

the document.

● For details about how to use the 4G Smart Dongle SDongleA-03, see the

SDongleA-03 Quick Guide (4G)

. You can also scan the QR code to obtain the

document.

The quick guide is delivered with the Smart Dongle.

5.4 Installing a WLAN Antenna

Procedure

Step 1 Remove the watertight cap from the ANT port.

Step 2 Install the washer to the ANT port on the chassis.

Step 3 Install the WLAN antenna.

SUN2000-(2KTL-6KTL)-L1

User Manual

5 Electrical Connection

Issue 04 (2021-04-01)

Summary of Contents for SUN2000-2KTL-L1



























































































































Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands

Huawei SUN2000-2KTL-L1, User Manual

Search results

Summary of Contents for SUN2000-2KTL-L1

Reviews:

Related manuals for SUN2000-2KTL-L1

Brands by name

Popular brands