background image

16

1. Turn on the AC switch between the SUN2000 and the power grid.
2. Ensure that the DC switches at the SUN2000 bottom are ON.
3. (Optional) Measure the temperatures at the joints between DC terminals and connectors using a 

point-test thermometer.

4. Observe the indicators to check the SUN2000 operating status.

To ensure that the DC terminals are in good contact, check the temperatures at the joints between 
DC terminals and connectors after the SUN2000 has been running for a period of time. Ensure 
that the temperature rise does not exceed 40

°

C.

NOTE

Indicator

Status

Meaning

PV connection 
indicator

Green on

At least one PV string is properly 
connected, and the DC input voltage of 
the corresponding MPPT circuit is 
higher than or equal to 200 V.

Green off

The SUN2000 disconnects from all PV 
strings, or the DC input voltage of each 
MPPT circuit is less than 200 V.

Grid-tied indicator

Green on

The SUN2000 has connected to the 
power grid.

Green off

The SUN2000 has not connected to the 
power grid.

Communications 
indicator

Blinking green (on for 0.5s and then off 
for 0.5s)

The SUN2000 receives 
communications data normally.

Green off

The SUN2000 receives no 
communications data for 10s.

Alarm/Maintenance 
indicator

Alarm status

Blinking red at long 
intervals (on for 1s and 
then off for 4s).

A warning alarm is generated.

Blinking red at short 
intervals (on for 0.5s and 
then off for 0.5s).

A minor alarm is generated.

Steady red

A major alarm is generated.

Local 
maintenance 
status

Blinking green at long 
intervals (on for 1s and 
then off for 1s)

Local maintenance is in progress.

Blinking green at short 
intervals (on for 0.125s 
and then off for 0.125s)

Local maintenance fails.

Steady green

Local maintenance succeeds.

SUN2000 App

7

1. The SUN2000 app is a mobile phone app that communicates with the SUN2000 monitoring 

system over a USB data cable, a Bluetooth module, or a WLAN module. As a convenient local 
monitoring and maintenance platform, it supports alarm query, parameter settings, and routine 
maintenance. The app name is 

SUN2000

2. Access Huawei application store (https://appstore.huawei.com) or Google Play 

(https://play.google.com), search for 

SUN2000

, and download the app installation package.

3. Connect a USB data cable, a Bluetooth module, or a WLAN module to the USB port of the 

SUN2000 to implement the communication between the SUN2000 and the app.

NOTE

Summary of Contents for SUN2000-29.9KTL




















Reviews: