manualshive.com logo in svg

Huawei SUN2000-196KTL-H0, User Manual

Share
Download
Huawei SUN2000-196KTL-H0 User Manual Download Page 94

Alarm

ID

Alarm Name

Alarm

Severity

Cause

Troubleshooting Suggestions

2062

Low Insulation

Resistance

Major

Cause ID=1
1. The PV string is short-

circuited to the PE

cable.

2. The PV string has been

in a moist environment

for a long time and the

circuit is not well

insulated to ground.

1. Check the impedance of

the PV string to PE. If a

short circuit occurs, rectify

it.

2. Check that the ground

cable of the inverter is

correctly connected.

3. If you are sure that the

impedance is less than the

preset value in a cloudy or

rainy environment, reset

Insulation resistance

protection.

2063

Cabinet

Overtemperatu

re

Minor

Cause ID=1
1. The inverter is installed

in a place with poor

ventilation.

2. The ambient

temperature is too high.

3. The inverter is not

working properly.

1. Check the ventilation and

whether the ambient

temperature of the inverter

exceeds the upper limit. If

the ventilation is poor or

the ambient temperature is

too high, improve

ventilation.

2. If both the ventilation and

ambient temperature meet

requirements yet the fault

persists, contact your

dealer or Huawei technical

support.

2064

Device Fault

Major

Cause ID=1
An unrecoverable fault has

occurred on a circuit inside

the inverter.

Turn off the AC output switch

and DC input switch, and then

turn them on after 15

minutes. If the fault persists,

contact your dealer or Huawei

technical support.

2065

Upgrade Failed

or Software

Version

Unmatch

Minor

Cause ID=1
The upgrade does not

complete normally.

1. Perform an upgrade again.
2. If the upgrade fails several

times, contact your dealer.

2066

License Expired Warning

Cause ID=1
1. The privilege license

has entered the grace

period.

2. The privilege feature

will be invalid soon.

1. Apply for a new license.
2. Load a new license.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

User Manual

8 Maintenance

Issue 02 (2020-10-30)

Copyright © Huawei Technologies Co., Ltd.

87

Summary of Contents for SUN2000-196KTL-H0














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands