Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 83 / 553

background image

Prerequisites

Before configuring the NTP broadcast mode, make sure that the network interface and the routing
protocol of the MA5616 are configured so that the server and the client are reachable to each
other at the network layer.

Context

In the broadcast mode, the server periodically sends clock synchronization packets to the
broadcast address 255.255.255.255, with the Mode field set to 5 (indicating the broadcast mode).
The client snoops on the broadcast packets sent from the server. After receiving the first
broadcast packet, the client exchanges NTP packet whose interaction mode fields are set to 3
(on the client) and 4 (on the server) with the server to obtain the network delay between the
client and the server. The client then enters the broadcast client mode, continues to snoop on the
incoming broadcast packets, and synchronizes the local clock according to the incoming
broadcast packets, as shown in

Figure 3-26

Figure 3-26

NTP broadcast mode

Precaution

1.

In the broadcast mode, you need to configure both the NTP server and the NTP client.

2.

The clock stratum of the synchronizing device must be smaller than or equal to that of the
synchronized device. Otherwise, the clock synchronization fails.

Procedure

l

Configure the NTP broadcast client host.

1.

(Optional) Configure NTP authentication.
In certain networks that have strict requirements on security, it is recommended that
you enable NTP authentication when running the NTP protocol. The configuration of
the server must be the same as that of the client.

a.

Run the

ntp-service authentication enable

command to enable NTP

authentication.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

72

«
...
81
82
83
84
85
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Mini Field Agent

Brand: GE Pages: 87

Elinx EIRP305-T

Brand: B&B Electronics Pages: 19

SR8800 IM-FW-II

Brand: H3C Pages: 107

Brand: 3Com Pages: 12

Brand: H3C Pages: 16

H3C S3600 Series

Brand: H3C Pages: 10

Brand: H3C Pages: 42

Brand: H3C Pages: 2

H3C S7500E Series

Brand: H3C Pages: 34

Brand: H3C Pages: 33

Brand: H3C Pages: 14

Brand: H3C Pages: 56

H3C S7500E Series

Brand: H3C Pages: 112

Brand: H3C Pages: 15

SR8800 IM-FW-II

Brand: H3C Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands