Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 494 / 553

background image

Configuration Products

lists the configuration products for the FTTx solution.

Table 10-1

Configuration products for the FTTx solution

Network
Positioni
ng

Configuration Product

Version

Description

OLT

MA5600T and MA5603T

V800R008C0
1/C02

Supports functioning as an
OLT in the FTTH, FTTB,
FTTC, Base station access, or
FTTO network.

MDU

MA5620, MA5626,
MA5612, MA5652G

V800R308C0
0

Supports functioning as an
MDU in the FTTB or FTTC
network.

MA5616, MA5628

V800R308C0
1

CBU

MA5612

V800R308C0
0/C01

Supports functioning as a
CBU in the Base station
access network.

SBU

MA5612

V800R308C0
0/C01

Supports functioning as an
SBU in the FTTO network.

ONT

HG series

V100R001/
V100R002

Supports functioning as an
ONT in the FTTH network.

10.2 FTTx Data Plan (GPON Access)

This topic plans the data in a unified manner for connecting to the OLT in the FTTx GPON
access mode for various example networks. The subsequent examples are configured based on
the following data plan.

Data Plan

provides the unified data plan for configuring the HSI, IPTV, VoIP, emulation

services, and private line services in an FTTx network.

NOTE

The ONU in the data plan refers to the ONT and the MDU collectively.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

483

«
...
492
493
494
495
496
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 40

ShareCenter Quattro DNS-345

Brand: D-Link Pages: 4

AirPlus G DWL-G710

Brand: D-Link Pages: 5

MYDLINK DNR-322L

Brand: D-Link Pages: 4

mydlink DNR-312L

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 16

Brand: D-Link Pages: 88

Brand: Delta Pages: 2

MegaRAID SATA 300-4XLP

Brand: LSI Pages: 3

ExpressBox2 EB2

Brand: Magma Pages: 74

Brand: 3Com Pages: 12

Brand: Alfa Network Pages: 11

MP5S Plus Writer

Brand: SONIX Pages: 23

NC-MCO - TECHNICAL

Brand: Crest Audio Pages: 2

Brand: Wistron NeWeb Pages: 32

Brand: Quatech Pages: 5

VAR-SOM-MX6 HEAT PLATE KIT

Brand: Variscite Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands