Huawei SmartAX MA5616 Configuration Manual Download

Page: 486 / 553

Figure 9-16

Example network of the triple play service in the multi-PVC for multiple services

mode

BMS

OSS & RADIUS Server/

RADIUS Proxy

BRAS

Router

LAN Switch

Multicase Sever

Softswitch

STB

IP Phone

MA5616

CPE

STB

IP Phone

CPE

0/3/0

0/3/1

IAD Voice

Gateway

IAD Voice

Gateway

Data Plan

Table 9-10

provides the data plan for configuring the triple play service in the multi-PVC for

multiple services mode.

Table 9-10

Data plan for configuring the triple play service in the multi-PVC for multiple

services mode

Item

Data

VDSE

Service ports: 0/1/0 and 0/1/1
Index of the VDSL2 line template bound to the port: 2, where:

Index of the VDSL2 line profile: 3

Index of the VDSL2 channel profile: 3

Index of the VDSL2 alarm template bound to the port: 2, where:

Index of the VDSL2 line alarm profile: 3

Index of the VDSL2 channel alarm profile: 3

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

475

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands