Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 454 / 553

background image

Figure 9-8

Example network of the VoIP PSTN service based on the SIP protocol

Data Plan

Run the

display system parameters

and

display oversea parameters

commands to query the

system parameters and overseas parameters. If the parameter settings do meet the requirements,
run the

system parameters

and

oversea parameters

commands to set the parameters to the

required values.

In this example, the MA5616 is used in China. The default configurations of system parameters
and overseas parameters can meet the standard and application requirements. Therefore, you
need not configure these parameters.

provides the data plan for configuring the VoIP PSTN service based on the SIP

protocol.

Table 9-4

Data plan for configuring the VoIP PSTN service based on the SIP protocol

Item

Data

SIP interface

SIP interface ID

0

Local digitmap

Digitmap name

huawei0 and huawei1

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

443

«
...
452
453
454
455
456
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Parker Pages: 344

Brand: Hal Communications Pages: 25

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: Garland Pages: 6

Brand: FS Pages: 19

FieldPoint cFP-RTD-122

Brand: National Instruments Pages: 15

Brand: Longshine Pages: 27

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

Brand: 3Ware Pages: 4

Brand: Kohler Pages: 32

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: uneron Pages: 13

Brand: COUGAR Pages: 2

Brand: Neousys Technology Pages: 39

Brand: Uctronics Pages: 12

Brand: DTS Pages: 94

SteelCentral NetExpress 470

Brand: Riverbed Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands