Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 437 / 553

background image

service-port desc 3 description MA5616HW/Vlanid:50/vdsl/smart
mac-address max-mac-count service-port 3 16
mac-pool xpoa 0000-1111-1010 300
ipoa enable
ipoa default gateway 192.168.1.20
encapsulation 0/1/0 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1
save

9.2 Configuration Example of the Multicast Service
(Multicast VLAN Mode)

This topic describes how to configure the multicast service on the MA5616 in multicast VLAN
mode.

9.2.1 Configuration Example of the Multicast Video Service (Static
Configuration Mode)

This topic describes how to configure the multicast video service if the program in the multicast
VLAN is configured statically.

Prerequisites

l

Network devices and lines must be in the normal state.

l

The multicast source must exist on the network and the IP address of the multicast source
must be known.

Context

The program in the multicast VLAN can be configured statically or generated dynamically.

For the static configuration mode:

l

The program list needs to be configured for the multicast VLAN. Then, the user can request
for the program in this program list.

l

The following functions are supported: bandwidth management of the multicast program,
user bandwidth management, program preview, and program prejoin.

l

The program in the multicast VLAN is configured statically by default.

Networking

shows the example network of the multicast service.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

426

«
...
435
436
437
438
439
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Univerge SV8100

Brand: NEC Pages: 44

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

SATA II ExpressCard 34

Brand: LaCie Pages: 2

12big Rack Fibre 8

Brand: LaCie Pages: 9

FrameSaver 9120

Brand: Paradyne Pages: 2

Brand: X-Micro Pages: 74

Brand: TFortis Pages: 86

BroadLink SP3353

Brand: MicroNet Pages: 66

IntroSpect Analyzer 2 Series

Brand: Aruba Pages: 5

Power Control Processor

Brand: ETC Pages: 64

Core 2 Quad Q9400

Brand: Intel Pages: 2

Brand: Keithley Pages: 98

Brand: Seattle Computer Products Pages: 31

Brand: IDT Pages: 292

HHM Series HHM2409

Brand: TDK Pages: 2

Brand: XtendLan Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands