manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

  Mean: Hooking upper threshold(ms), reference: China:350, HongKong:800
  -----------------------------------------------------------------------------
  Parameter name index: 1     Parameter value: 100
  Mean: Hooking lower threshold(ms), reference: China:100, HongKong:100
  -----------------------------------------------------------------------------
  Parameter name index: 2     Parameter value: 0
  Mean: Flag of applying PARKED LINE FEED or not when user port is locked, 0:not
 apply, 1:apply
  -----------------------------------------------------------------------------
  Parameter name index: 3     Parameter value: 1
  Mean: Type of ring DC offset, 0:Line A offset, 1:Line B offset
  -----------------------------------------------------------------------------

7.2.2.5 (Optional) Configuring the Local Digitmap

Local digitmap is also called local preconfigured digitmap. When the H.248 protocol is used,
the MA5616 prefers to use the digitmap sent by the MGC to match the phone number. If the
MGC does not send the detailed digitmap, the MA5616 uses the local digitmap to match the
phone number. When the SIP protocol is used, the MA5616 has to use the local digitmap to
match the phone number because the IMS network does not send the digitmap. When configuring
services on the MA5616, configure a proper local digitmap according to the local standards.

Context

CAUTION

When the H.248 protocol is used, the local digitmap need not be configured by default. You can
configure the local digitmap according to the requirements.

l

When the H.248 protocol is used, the MA5616 is not configured with a default local
digitmap. You can configure a local digitmap if required.

l

When the SIP protocol is used, the MA5616 is configured with three default local digitmaps,
namely, normal digitmap, emergency digitmap, and SCC digitmap. You can change the
name and type of the default local digitmaps, and add or change the digitmap body in the
default local digitmaps. In addition, you can add a local digitmap according to the
requirements. 

Table 7-16

 lists the information about the default local digitmap.

Table 7-16

 Information about the default local digitmap when the SIP protocol is used

Digitmap Name

Digitmap Type

Digitmap Body

DefaultNormalDmm

normal

x.S

DefaultSccDmm

scc

([EF]X[0-9E].F|[EF]X
[0-9E].S|[EF][EF]X
[0-9E].F|[EF][EF]X
[0-9E].S)

DefaultEmergencyDmm

emergency

(11X|91X)

 

l

The MA5616 supports a maximum of eight local digitmaps.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

259

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Canon C50FSi - VB Network Camera Setup Manual preview
C50FSi - VB Network Camera
Brand: Canon Pages: 32
Rabbit 2000 Reference Manual preview
2000
Brand: Rabbit Pages: 120
IBM 3270 Operation Manual preview
3270
Brand: IBM Pages: 86
Maxim DS5001FP Specification Sheet preview
DS5001FP
Brand: Maxim Pages: 26
NetComm 3GM1WN Quick Start Manual preview
3GM1WN
Brand: NetComm Pages: 3
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
SIIG NN-EC2812-S1 Quick Installation Manual preview
NN-EC2812-S1
Brand: SIIG Pages: 12
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Brand: Barco Pages: 121
N.A.T. NAT-MCH Technical Reference Manual preview
NAT-MCH
Brand: N.A.T. Pages: 32
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
UHP UHP-1200 Installation Manual preview
UHP-1200
Brand: UHP Pages: 15
Ubiquiti LiteBeam M5-23 Quick Start Manual preview
LiteBeam M5-23
Brand: Ubiquiti Pages: 21
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
IBASE Technology FWA8207 Series User Manual preview
FWA8207 Series
Brand: IBASE Technology Pages: 39
Nilox 16NX071900001 User Manual preview
16NX071900001
Brand: Nilox Pages: 66
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
Vecow SPC-2845 User Manual preview
SPC-2845
Brand: Vecow Pages: 61

Brands by name

Popular brands

Load more brands