Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 261 / 553

background image

MGID
0
Signalling IP
10.13.4.117
Signalling Port
5000
Media IP
10.13.4.116
Transfer Mode
UDP
Primary Proxy IP 1
10.13.4.118
Primary Proxy IP 2
-
Primary Proxy Port
5060
Secondary Proxy IP 1
10.13.4.119
Secondary Proxy IP 2
-
Secondary Proxy Port
5060
Proxy Address Mode
IP
SIPProfile Index
1:Default
Service logic Index
0:Default
Server Address DHCP Option
0:None
Primary Proxy Domain Name
-
Secondary Proxy Domain Name
-
Home Domain Name
sip.huawei.com
Description
-
MG Domain Name
-
Phone Context
-
Register URI
-
Conference Factory URI
-
Primary Proxy State
up
Secondary Proxy State
up
Subscribe to UA-Profile enable
Subscribe to REG-STATE disable
Subscribe to MWI disable
SDP negotiation mode remote
Mode of supporting proxy dual-homing dualhome
Proxy detection mode probe
------------------------------------------------------------

7.2.1.4 (Optional) Configuring the Ringing Mode of the SIP Interface

This topic describes how to configure the ringing mode of the SIP interface to support the break-
make ratios of various new ringing modes and make the ringing mode meet the local standards.

Prerequisites

The SIP interface must be added successfully.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

250

«
...
259
260
261
262
263
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

SAFETank Series

Brand: Raidon Pages: 49

Brand: M86 Security Pages: 46

Brand: Winext Pages: 37

Brand: Intellinet Pages: 2

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

Brand: Campbell Pages: 38

Brand: Lucent Technologies Pages: 20

Brand: Gbord Pages: 8

Brand: BinTec Pages: 34

Brand: Loopcomm Pages: 2

Brand: Ubiquiti Pages: 23

Brand: S&T Pages: 28

CloudGen Firewall

Brand: Barracuda Pages: 8

Brand: ExtraHop Pages: 3

Brand: Alloy Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands