Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 259 / 553

background image

IP Address...........: 10.13.4.116
Subnet Mask..........: 255.255.0.0
MAC Address..........: 00-E0-FC-AF-91-33

IP Address...........: 10.13.4.117
Subnet Mask..........: 255.255.0.0
MAC Address..........: 00-E0-FC-AF-91-33

7.2.1.3 Adding an SIP Interface

This topic describes how to add an SIP interface so that the MA5616 can communicate with the
IMS through the SIP interface.

Prerequisites

The to-be-configured media and signaling IP addresses of the SIP interface must be added to
the media and signaling IP address pools successfully.

Context

One MA5616 supports only one SIP interface.

Procedure

Step 1

Run the

display protocol support

command to query the current system protocol.

l

If the system protocol is SIP, go to

l

If the system protocol is not SIP, go to

Step 2

Run the

display if-h248 all

command to query whether an MG interface that supports the current

protocol exists in the system.

Step 3

Run the

display mgpstnuser

command to check the user data, run the

esl user

command to

enter ESL user mode, and then run the

mgpstnuser batdel

command to delete the voice service

user.

Step 4

Run the

shutdown(h248)

command to shut down the MG interface.

CAUTION

This operation interrupts the ongoing services carried on the currently used MG interface. Hence,
exercise caution when performing this operation. Before performing this operation, be sure to
check whether the operation is allowed.

Step 5

Run the

undo interface h248

command to delete the MG interface.

Step 6

Run the

protocol support sip

command to change the system protocol to SIP.

CAUTION

You must delete the default and user-defined local digitmaps before switching the protocol.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

248

«
...
257
258
259
260
261
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

TokenLink 3C359B

Brand: 3Com Pages: 4

TokenLink 3C359B

Brand: 3Com Pages: 8

TokenLink 3C339

Brand: 3Com Pages: 2

EtherLink 3C985B-SX

Brand: 3Com Pages: 44

Brand: 3Com Pages: 88

Brand: 3Com Pages: 2

Brand: 3Com Pages: 111

TokenLink 3C359

Brand: 3Com Pages: 4

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Storagelibrary T24

Brand: Tandberg Data Pages: 28

Parallel Printer Card PIOC

Brand: B&B Electronics Pages: 16

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

Brand: ICP DAS USA Pages: 8

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brand: ebm-papst Pages: 13

Brand: IMC Networks Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands