Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 240 / 553

background image

Command:
display mg-ringmode attribute
-------------------------------------------------------
MGID PeerPara CadenceRing InitialRing
-------------------------------------------------------
0 1 128 144
-------------------------------------------------------

7.1.1.7 (Optional) Configuring the TID Format of an MG Interface

The TID format determines how various user terminal IDs on the MG interface are generated.

Context

CAUTION

The configuration of the TID format is relatively complicated. The information such as the syntax
rules with which the terminal prefix must comply and the requirements for the character string
of the TID template is defined in the protocol, and is not described here. This topic describes
only some basic information. It is recommended that you refer to the TID description in ITU-T
H248.1 before configuring the TID format.

The TID format consists of the terminal prefix and the TID template. The TID template defines
the generation mode of the TID excluding the terminal prefix. A TID consists of a terminal prefix
and a character string generated by a TID template.

The TID templates that are bound to various types of users on the MG interface determine
whether the users support terminal layering.

l

If the parameter list of the TID template includes only keyword "G", it indicates that the
TID template is used by the non-layering users. Users bound with this template do not
support terminal layering.

l

If the parameter list of the TID template includes only keywords "F", "S", "P", "B" ("B" is
not available to PSTN users), it indicates that the TID template is used by the layering users.
Users bound with this template support terminal layering.

NOTE

The meaning of each keyword is as follows:

l

F indicates the shelf ID.

l

S indicates the slot ID.

l

P indicates the port ID.

l

B indicates the B channel ID (only for ISDN BRA and ISDN PRA terminals).

l

G indicates the general permanent termination index.

l

R indicates the RTP ephemeral termination index (only for the RTP ephemeral termination, which
exists only when the system protocol is H.248. This termination is not involved unless special remarks
are provided.)

When adding a user that supports terminal layering, you cannot specify the parameter

terminalid

because the system automatically allocates a terminal ID. When adding a user that

does not support terminal layering, you must specify the parameter

terminalid

.

You can run the

display tid-format

command to query the TID formats of various types of users

on the current MG interface. In the query result,

template-index

indicates the index of the TID

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

229

«
...
238
239
240
241
242
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 29

DGS-3700 Series

Brand: D-Link Pages: 292

Brand: D-Link Pages: 140

DGS-1224T - Web Smart Switch

Brand: D-Link Pages: 61

DI-LB604 - Load Balancing Router

Brand: D-Link Pages: 14

Brand: D-Link Pages: 2

Brand: D-Link Pages: 45

Brand: D-Link Pages: 218

DES-3528 - xStack Switch - Stackable

Brand: D-Link Pages: 322

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 10

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 4

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 13

Brand: D-Link Pages: 13

DI-804HV - Express ENwork Router

Brand: D-Link Pages: 19

Brand: D-Link Pages: 12

Brand: D-Link Pages: 8

Brand: D-Link Pages: 16

Brand: D-Link Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands