Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 24 / 553

background image

Figure 3-2

Flowchart for configuring management through a local serial port

Start

Connect the serial port cable

Start the HyperTerminal

Set parameters of the

HyperTerminal

Set the terminal emulation

type

Set the line delay and the

character delay

Log in to the system

End

Procedure

Step 1

Connect the serial port cable.

Use a standard RS-232 serial port cable to connect the serial port of the PC to the CONSOLE
port (maintenance serial port) on the control board of the MA5616, as shown in

.

Step 2

Start the HyperTerminal.
1.

Set up a connection.

Choose

Start

>

Programs

>

Accessories

>

Communications

>

HyperTerminal

on the

PC. The

Connection Description

dialog box is displayed. Enter the connection name, as

shown in

, and click

OK

.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

13

«
...
22
23
24
25
26
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 5

Brand: D-Link Pages: 2

OfficeConnect 1600

Brand: 3Com Pages: 8

Brand: 3Com Pages: 8

SAFETank Series

Brand: Raidon Pages: 49

xCORE-200 Multi-channel Audio board

Brand: XMOS Pages: 112

Brand: Profile Pages: 6

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

Brand: Measurement Computing Pages: 27

Brand: Sangoma Pages: 6

Brand: PMD Pages: 74

Brand: Conel Pages: 32

Brand: DigiTech Pages: 6

Brand: Comtrend Corporation Pages: 4

Brand: Linksys Pages: 6

Brand: MaxComm Pages: 10

Brand: Holtek Pages: 280

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands