Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 184 / 553

background image

5.5 (Optional) Configuring the xPoA-xPoE Protocol
Conversion

Configuring protocol conversion is required only when the encapsulation mode is IPoA or
PPPoA; it is not required when the encapsulation mode is IPoE or PPPoE.

Context

In the xPoA access mode, data cannot be directly transmitted in the IP network, and protocol
conversion is required. IPoA data and PPPoA data can be transmitted in the IP network only
after the IPoA-IPoE and PPPoA-PPPoE conversions are performed.

The principle of the IPoA protocol is different from that of the PPPoA protocol. In the PPPoA
mode, the BRAS automatically allocates a gateway address to the PPPoA user after the PPPoA
user passes the authentication on the BRAS and dialup is successful. Therefore, the default
gateway address need not be configured in the PPPoA mode. IPoA data is forwarded according
to the route to the destination IP address and the next hop IP address needs to be configured.
Therefore, the default gateway address needs to be configured in the IPoA mode.

provides the configuration flow for the xPoA-xPoE protocol conversion.

Figure 5-2

Flowchart for configuring the xPoA-xPoE protocol conversion

lists the default settings of the xPoA-xPoE protocol conversion.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

5 Configuring the xDSL Internet Access Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

173

«
...
182
183
184
185
186
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 5

Brand: D-Link Pages: 2

Brand: NEC Pages: 72

Brand: TDC Pages: 27

ELECTRA ELITE IPK II

Brand: NEC Pages: 617

VERSA DOCK - SERVICE

Brand: NEC Pages: 8

Brand: Ubee Pages: 9

Brand: Commell Pages: 36

Brand: IEI Technology Pages: 3

Brand: Supero Pages: 68

Fast SwitchHub-8mi SNMP

Brand: Accton Technology Pages: 13

Brand: Roland Pages: 2

Brand: Realtek Pages: 30

Brand: Quantum Pages: 7

AT32F421 Series

Brand: ARTERY Pages: 337

Brand: Advantech Pages: 68

Brand: Patton electronics Pages: 145

Brand: Linksys Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands