Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 179 / 553

background image

NOTE

To activate a port, you must bind the port with a line template. If you do not specify the index
of the line template, the system uses the template bound with the port last time to activate the
port.

–

In the case of VDSL TI mode, run the

activate portid spectrum-profile-index

spectrum-profile-index dpbo-profile-index dpbo-profile-index upbo-profile-
index upbo-profile-index service-profile-index service-profile-index noise-
margin-profile-index noise-margin-profile-index delayinp-profile-index
delayinp-profile-index

command to activate a VDSL2 port and bind the port with

VDSL2 profiles.

3.

Run the

alarm-config

command to bind an alarm template to the port.

----End

Example

To activate ADSL2+ port 0/2/0 and bind line template 2 and alarm template 2 to it, do as follows:

huawei(config)#

interface adsl 0/2

huawei(config-if-adsl-0/2)#

deactivate 0

huawei(config-if-adsl-0/2)#

activate 0 profile-index 2

huawei(config-if-adsl-0/2)#

alarm-config 0 2

To activate SHDSL port 0/4/0 and bind line profile 2 and alarm profile 2 to it, do as follows:

huawei(config)#

interface shl 0/4

huawei(config-if-shl-0/4)#

deactivate 0

huawei(config-if-shl-0/4)#

activate 0 2

huawei(config-if-shl-0/4)#

alarm-config 0 2

In the common VDSL mode, to activate VDSL2 port 0/1/0 and bind line template 2 and alarm
template 2 to it, do as follows:

huawei(config)#

interface vdsl 0/1

huawei(config-if-vdsl-0/1)#

deactivate 0

huawei(config-if-vdsl-0/1)#

activate 0 template-index 2

huawei(config-if-vdsl-0/1)#

alarm-config 0 2

5.4 Creating an xDSL Service Port

A service port is a service channel connecting the user side to the network side. To provide
services, a service port must be created.

Context

A service port can carry a single service or multiple services. When a service port carries multiple
services, the MA5616 supports the following modes of traffic classification:

l

By user-side VLAN

l

By user-side service encapsulation mode

l

By VLAN+user-side packet priority

l

By VLAN+user-side service encapsulation mode

lists the default settings of a service port.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

5 Configuring the xDSL Internet Access Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

168

«
...
177
178
179
180
181
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Rabbit Pages: 45

Brand: Rabbit Pages: 174

Brand: Rabbit Pages: 43

Brand: Xinje Pages: 76

Adapter Bracket

Brand: Paradyne Pages: 1

Brand: Dialogic Pages: 2

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

Brand: IDT Pages: 93

Brand: Seattle Computer Products Pages: 31

Brand: TP-Link Pages: 2

Brand: Cervoz Pages: 22

Quadro M6000 Sync

Brand: Nvidia Pages: 8

SiliconDrive SSD-P16G(I)-3100

Brand: Silicon Systems Pages: 108

Brand: AMD Pages: 45

Brand: ADIC Pages: 140

Brand: AMX Pages: 1

Brand: Alula Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands