Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 180 / 553

background image

Table 5-6

Default settings of a service port

Parameter

Default Setting

Traffic profile ID

0-6

Administration status

Activated

Maximum number of learnable MAC
addresses

255

Procedure

Step 1

Add a traffic profile.

Run the

traffic table ip

command to add a traffic profile. There are seven default traffic profiles

in the system with the IDs of 0-6.

Before creating a service port, run the

display traffic table

command to check whether the

traffic profiles in the system meet the requirement. If no traffic profile in the system meets the
requirement, add a traffic profile that meets the requirement. For details about the traffic profile,
see

3.14.1.1 Configuring Traffic Management Based on Service Port

Step 2

Create a service port.

You can choose to create a single service port or multiple service ports in batches according to
requirements.

l

Run the

service-port

command to create a single service port. Service ports are classified

into single-service service ports and multi-service service ports. Multi-service service ports
are generally applied to the triple play service scenario.

–

Single-service service ports:
Select

single-service

or do not input

multi-service

to create a single-service service

port.

–

Multi-service service port based on the user-side VLAN:
Select

multi-service user-vlan

{

untagged

|

user-vlanid

|

priority-tagged

|

other-

all

}.

–

untagged

: When

untagged

is selected, user-side packets do not carry a tag.

–

user-vlanid

: When

user-vlanid

is selected, user-side packets carry a tag and the value

of

user-vlanid

must be the same as the tag carried in user-side packets. The user-

side VLAN is the C-VLAN.

–

priority-tagged

: When

priority-tagged

is selected, the VLAN tag is 0 and the

priorities of user-side packets are 0-7.

–

other-all

: When

other-all

is selected, service ports for the transparent LAN service

(TLS) are created, which are mainly used in the QinQ transparent transmission
service for enterprises. All the traffic except known traffic in the system is carried
by this channel.

–

By user-side service encapsulation mode
Select

multi-service user-encap

user-encap

.

–

By VLAN + user-side packet priority (802.1p)

SmartAX MA5616 Multi-service Access Module
Configuration Guide

5 Configuring the xDSL Internet Access Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

169

«
...
178
179
180
181
182
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Express5800/E120d-M

Brand: NEC Pages: 2

Brand: H3C Pages: 16

Brand: H3C Pages: 24

Device Server UDS 10

Brand: Lantronix Pages: 8

Brand: IBM Pages: 63

MegaRAID SATA 300-4XLP

Brand: LSI Pages: 3

Brand: Qixiang Technology Pages: 16

Brand: Kaptia Pages: 14

Brand: Intel Pages: 26

Brand: H3C Pages: 4

Brand: Powerleap Pages: 28

FireWire 800 ExpressCard 34

Brand: LaCie Pages: 24

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Brand: 3Com Pages: 12

Brand: ZALMAN Pages: 20

Brand: DTS Pages: 94

Service Aggregation Router 7705

Brand: Alcatel-Lucent Pages: 20

Brand: Lucent Technologies Pages: 7

Brand: Stephen Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands