Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 14 / 553

background image

Table 1-2

Activities involved in network device deployment in the scenario without the NMS

Activities

Description

ONU data plan

NOTE

The ONU refers to
MA5616.

Perform the data plan for the OLT and ONU according to the
actual FTTx service plan and the corresponding OLT version.

ONU installation

The hardware installation engineer draws the ONU from the
storehouse and installs it at the destination site. After installing it
and confirming that the hardware is fault-free, the hardware
installation engineer returns the ONU type, service port
information, and ONU SN to the commissioning engineer.

ONU deployment

Enable the auto-discovery function on the PON port through the
CLI command of the OLT, confirm the automatically discovered
ONU, and add the ONU by using the preconfigured profile.

Configuration of the
services of the ONU

You can telnet to the ONU according to the management IP
address of the ONU to configure the services for the ONU.

1.2 Example of Deploying Network Devices

This topic describes how to deploy network devices in the scenario with or without the NMS.

Prerequisites

l

Network devices and lines must be in the normal state.

l

The control board and the GPON service board of the OLT must be in the normal state.

Context

When the ONU adopts the GPON upstream transmission, the SN is used for authentication.

Scenario with the NMS

shows an example network of device deployment in the scenario with the NMS.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

1 Deploying Network Devices

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

3

«
...
12
13
14
15
16
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: 3xLogic Pages: 2

Brand: Abocom Pages: 1

Brand: REXROTH Pages: 68

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

Brand: Waves Pages: 41

Brand: Digi Pages: 116

Brand: Caen Pages: 14

Brand: LevelOne Pages: 26

Brand: Westermo Pages: 34

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

500 - DATASHEET REV 003

Brand: Intel Pages: 67

Brand: Connectland Pages: 10

Brand: Linksys Pages: 80

Brand: Homeworks Pages: 24

Brand: LevelOne Pages: 2

Brand: ADLINK Technology Pages: 86

Brand: Advantech Pages: 70

Brand: IBM Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands