Huawei SmartAX MA5616 Configuration Manual Download

Page: 12 / 553

Deploying Network Devices

About This Chapter

Deploy the ONUs at sites according to network planning so that the NMS, OLT, and ONU can
communicate with each other.

1.1 Introduction to the Network Device Deployment

This topic describes how to deploy network devices, including optical network unit (ONU) data
plan, ONU offline deployment (through the NMS or the CLI of the OLT), ONU installation,
and ONU binding. After the deployment, you can remotely configure services for the ONU.

1.2 Example of Deploying Network Devices

This topic describes how to deploy network devices in the scenario with or without the NMS.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

1 Deploying Network Devices

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands