In this example, the default SIP service data profile, namely SIP service data profile 1 is
used.
4.
Configure a POTS port profile.
Run the
display ont-pots-profile
command to query the existing POTS port profile in the
system. If the existing POTS port profile in the system does not meet the requirements, run
the
ont-pots-profile add
command to add a POTS port profile.
In this example, the default POTS port profile, namely POTS port profile 1 is used.
5.
Configure a digitmap profile.
Run the
display ont-digitmap-profile
command to query the existing digitmap profile in
the system. If the existing digitmap profile in the system does not meet the requirements,
run the
ont-digitmap-profile add
command to add a digitmap profile.
In this example, the default digitmap profile, namely digitmap profile 1 is used.
Step 4
Configure an IP address for an ONU SIP user.
For ONU 1 and ONU 2, configure the IP address obtaining mode to the DHCP mode, set the
management VLAN to VLAN 20, and use default values for other parameters.
huawei(config)#
interface gpon 0/1
huawei(config-if-gpon-0/1)#
ont ipconfig 0 1 dhcp vlan 20
huawei(config-if-gpon-0/1)#
ont ipconfig 0 2 dhcp vlan 20
Step 5
Configure SIP POTS users.
1.
Add an SIP interface and apply an SIP agent profile to the interface.
For ONU 1 and ONU 2, set the MG ID to 1, apply SIP agent profile 2 to ONU 1 and ONU
2, and use default values for other parameters.
If parameters in an SIP agent profile are changed, the SIP agent profile must be reapplied
to the ONU so that the changed parameters can take effect.
huawei(config-if-gpon-0/1)#
if-sip add 0 1 1 sipagent-profile profile-id 2
huawei(config-if-gpon-0/1)#
if-sip add 0 2 1 sipagent-profile profile-id 2
2.
Add POTS users.
For ONU 1 and ONU 2, set the MG ID to 1 (identical to the MG ID of the added SIP
interface), create two POTS users named huawei1 and huawei2, set passwords to user1 and
user2, set their phone numbers to 77730010 and 77730020 and use default values for other
parameters.
huawei(config-if-gpon-0/1)#
sippstnuser add 0 1 1 mgid 1 username huawei1 telno
77730010
huawei(config-if-gpon-0/1)#
sippstnuser add 0 2 1 mgid 1 username huawei2 telno
77730020
Run the
display sippstnuser attribute
command to check whether the configuration of
the POTS user is properly set.
huawei(config-if-gpon-0/1)#
display sippstnuser attribute 0 1 1
------------------------------------------------------------------------------
F/S/P : 0/1/0
ONT ID : 1
Port ID : 1
MG ID : 1
Telephone NO. : 77730010
User name : huawei1
Password : user1
...//The rest of the response information is omitted.
huawei(config-if-gpon-0/1)#
display sippstnuser attribute 0 2 1
SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
12 FTTO Configuration(SOHO and SME)
Issue 01 (2014-04-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1220
