Huawei RRU5303 Installation Manual Download Page 9

Page: 9 / 135

RRU5303
Installation Guide

1 Changes in RRU5303 Installation Guide

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Changes in RRU5303 Installation Guide

This section describes the changes in the

RRU5303 Installation Guide

Draft B (2018-05-15)

This is a draft.

Compared with Draft A (2018-04-14), this issue does not include any new information.

Compared with Draft A (2018-04-14), this issue includes the following change:

Topic

Change Description

11.1 Adding a Female Connector (Pressfit
Type) to the RRU Power Cable on the RRU
Side

Optimized the descriptions in this section.

Compared with Draft A (2018-04-14), no information is deleted from this issue.

Draft A (2018-04-14)

This is a draft.

Summary of Contents for RRU5303








































































































































Search results

Summary of Contents for RRU5303

Reviews:

Related manuals for RRU5303

Brands by name

Popular brands

Huawei RRU5303, Installation Manual

Search results

Summary of Contents for RRU5303

Reviews:

Related manuals for RRU5303

Brands by name

Popular brands