Huawei RRU5303 Installation Manual Download Page 55

Page: 55 / 135

RRU5303
Installation Guide

7 Installing the RRU

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

Installing the RRU

About This Chapter

This chapter describes the procedure for installing the RRU. The procedure for installing the
RRU varies depending on installation options.

7.1 Mounting Kits for an RRU

This section describes the bracket assembly and the attachment plate for an RRU.

7.2 Installing the RRU on a Pole

One or more RRUs can be installed on a pole.

7.3 Installing an RRU on U-steel

This section describes the procedure and precautions for installing an RRU on U-steel. An
RRU can be installed on U-steel secured on the ground or a tower. Each piece of U-steel
allows only one RRU to be installed in standard or reverse mode.

7.4 Installing an RRU on Angle Steel

This section describes the process and precautions for installing an RRU on angle steel. An
RRU can be installed on angle steel secured on the ground or a tower. Each piece of angle
steel allows only one RRU to be installed in standard or reverse mode.

7.5 Installing an RRU on a Wall

This section describes the procedure and precautions for installing an RRU on a wall.

7.6 Installing an RRU on an IFS06

This section describes the process and precautions for installing an RRU on an IFS06.

7.1 Mounting Kits for an RRU

This section describes the bracket assembly and the attachment plate for an RRU.

Figure 7-1 shows the front and side of an RRU.

Summary of Contents for RRU5303








































































































































Search results

Summary of Contents for RRU5303

Reviews:

Related manuals for RRU5303

Brands by name

Popular brands

Huawei RRU5303, Installation Manual

Search results

Summary of Contents for RRU5303

Reviews:

Related manuals for RRU5303

Brands by name

Popular brands