Huawei RRU5303 Installation Manual Download Page 102

Page: 102 / 135

RRU5303
Installation Guide

8 Installing RRU Cables

Issue Draft B (2018-05-15)

Huawei Proprietary and Confidential

excessively long distance between the equipment and the position where the cable is
secured.



Coil the excess of the fiber optic cables near the equipment on the tower before securing
the cables on the tower.

8.2 RRU Cable Connections

This section describes RRU cable connections.

The RRU does not support power cable cascading.

Figure 8-9 and Figure 8-10 show the cable connections of a single-mode RRU.

When the following scenarios need to be monitored by RRUs,



If the external power supply system needs to be monitored and supports modulating RS485 and dry
contact alarm signals using power cables, you do not need to install the MEB.



In other scenarios, you need to install MEB. For details about MEB and MEB cable installation, see

MEB06D User Guide

Figure 8-9

Cable connections of a single-mode RRU (MEB not installed)

(1) RRU PGND cable

(2) RRU RF jumper

(3) RRU AISG multi-wire cable

(4) RRU AISG extension cable

(5) RRU power cable

(6) CPRI optical fiber

Summary of Contents for RRU5303








































































































































Search results

Summary of Contents for RRU5303

Reviews:

Brands by name

Popular brands

Huawei RRU5303, Installation Manual

Search results

Summary of Contents for RRU5303

Reviews:

Brands by name

Popular brands