Huawei RRU3632 Installation Manual Download Page 33 | Manualshive

Page: 33 / 129

background image

l

The IFS06 supports at least three RRUs when the ambient temperature is higher than or
equal to the lowest operating temperature of the RRU and at least 5°C (41°F) lower than
the highest operating temperature of the RRU. The IFS06 supports a maximum of six RRUs
when the ambient temperature is higher than or equal to the lowest operating temperature
of the RRU and at least 10°C (50°F) lower than the highest operating temperature of the
RRU.

NOTE

For details about the operating temperature of the RRU, see section "Technical Specifications of
RRUs" in

3900 Series Base Station Technical Description

.

NOTICE

The mounting brackets for multiple RRUs cannot be combined when the RRUs are installed on
an IFS06, as shown in

Figure 3-21

Figure 3-21

Correct installation of mounting brackets for RRUs installed on an IFS06

Figure 3-22

and

Figure 3-23

show RRUs installed on an IFS06.

RRU3832&RRU3632
Installation Guide

3 Information About the Installation

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

24

«
...
31
32
33
34
35
...
»

Summary of Contents for RRU3632


































































































































Reviews:

No comments

Related manuals for RRU3632

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: B2 Pages: 52

MatrixPRO-II DVI 16x16

Brand: Barco Pages: 43

Brand: Barco Pages: 5

Brand: Cambium Networks Pages: 29

Device Server UDS 10

Brand: Lantronix Pages: 8

Brand: D-Link Pages: 83

Brocade X6-8 Director

Brand: Broadcom Pages: 207

Brand: Juniper Pages: 190

Brand: Dialogic Pages: 2

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

Brand: Watchguard Pages: 30

Brand: Hama Pages: 6

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: ZALMAN Pages: 9

Brand: C-Smartlink Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands