Huawei RRU3632 Installation Manual Download Page 12

Page: 12 / 129

Installation Preparations

About This Chapter

This chapter describes the reference documents, tools, and instruments that must be ready before
the installation. In addition, it specifies the skills and prerequisites that installation engineers
must have.

2.1 Reference Documents

Before the installation, you must be familiar with reference documents.

2.2 Tools and Instruments

You must prepare the following tools and instruments before the installation.

2.3 Skills and Requirements for Onsite Personnel

Onsite personnel must be qualified and trained. Before performing any operation, onsite
personnel must be familiar with correct operation methods and safety precautions.

RRU3832&RRU3632
Installation Guide

2 Installation Preparations

Issue 05 (2014-06-30)

Huawei Proprietary and Confidential

Summary of Contents for RRU3632


































































































































Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands

Huawei RRU3632, Installation Manual

Search results

Summary of Contents for RRU3632

Reviews:

Related manuals for RRU3632

Brands by name

Popular brands