Huawei RRU3262 Installation Manual Download Page 115

Page: 115 / 130

Step 5

Route the cables according to the instructions in

9.1 Cabling Requirements

, and then use cable

ties to bind the cables.

Step 6

Label the installed cables according to the instructions in Attaching an L-Shaped Label.

----End

9.9 Opening the Cover Plate of an RRU Cabling Cavity

This section describes the procedure for opening the cover plate of an RRU cabling cavity.

Procedure

Step 1

Wear ESD gloves.

NOTICE

Take proper ESD protection measures, for example, wear ESD gloves, to prevent electrostatic
damage to the boards, modules, or electronic components.

Step 2

Use an M5 Phillips screwdriver to loosen the three screws on the cover plate of the RRU cabling
cavity, and open the cover plate, as shown in

Figure 9-21

Opening the cover plate of the RRU cabling cavity

(1) Cover plate

(2) Cabling cavity

(3) Clip

(4) Cable trough for the power cable

(5) Waterproof block (6) Cable trough for the fiber optical cable

RRU3262
Installation Guide

9 Installing RRU Cables

Issue 01 (2014-11-20)

Huawei Proprietary and Confidential

107

Summary of Contents for RRU3262



































































































































Search results

Summary of Contents for RRU3262

Reviews:

Huawei RRU3262, Installation Manual, Page: 115 / 130

Search results

Summary of Contents for RRU3262

Reviews: