Huawei RRU3201 Installation Manual Download Page 36

Page: 36 / 96

Hoisting an RRU and Related Cables onto a

Tower

About This Chapter

This section describes the procedure for hoisting an RRU and related cables onto a tower and
the precautions that must be taken.

6.1 Hoisting an RRU onto a Tower

Before installing an RRU on a tower, bind the RRU and mounting kits and then hoist them onto
the tower. The RRU can be installed on a pole, U-steel, or angle steel. This section describes the
procedure for hoisting the RRU and mounting kits onto the tower and the precautions that must
be taken.

6.2 Hoisting Fiber Optic Cables onto a Tower

This section describes the procedure for hoisting fiber optic cables onto a tower and the
precautions that must be taken.

6.3 Hoisting Power Cables onto a Tower

This section describes the procedure for hoisting power cables onto a tower and the precautions
that must be taken.

RRU3201
Installation Guide

6 Hoisting an RRU and Related Cables onto a Tower

Issue 06 (2012-04-16)

Huawei Proprietary and Confidential

Summary of Contents for RRU3201

































































































Search results

Summary of Contents for RRU3201

Reviews:

Related manuals for RRU3201

Brands by name

Popular brands

Huawei RRU3201, Installation Manual

Search results

Summary of Contents for RRU3201

Reviews:

Related manuals for RRU3201

Brands by name

Popular brands