Huawei NetCol8000-A013 User Manual Download Page 38

Page: 38 / 181

Figure 3-2 Oil trap (unit: mm)

Gas Pipe, Liquid Pipe, and Thermal Insulation Foam (Optional)

Table 3-4

lists the specifications for pipes and thermal insulation foam.

Table 3-4 Specifications

Item

Specifications

Liquid pipe

3/8 inch (9.52 mm), wall thickness: 0.75 mm; pressure

withstanding capacity ≥ 4.5 MPa

Gas pipe

3/4 inch (19.05 mm), wall thickness: 1.0 mm; pressure

withstanding capacity ≥ 4.5 MPa

Thermal insulation

foam

≥ 13 mm

Water Pipe

Figure 3-3

shows how to connect a drainpipe.

NetCol8000-A013 In-room Air Cooled Smart Cooling

Product

User Manual (600 mm Width)

3 Installation Guide

Issue 02 (2020-11-09)

Summary of Contents for NetCol8000-A013






















































































































































































Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands

Huawei NetCol8000-A013, User Manual

Search results

Summary of Contents for NetCol8000-A013

Reviews:

Related manuals for NetCol8000-A013

Brands by name

Popular brands