manualshive.com logo in svg

Huawei ME936, Hardware Manual

Share
Download
Huawei ME936 Hardware Manual Download Page 49

 

HUAWEI ME936 LTE M.2 Module 
Hardware Guide   

RF Specifications 

 

Issue 03 (2017-12-11) 

Huawei Proprietary and Confidential 

Copyright © Huawei Technologies Co., Ltd. 

49 

 

Table 4-3  

ME936 GPS specifications 

TTFF 

Cold start 

37s/

–130 dBm 

Warm start 

37s/

–130 dBm 

Hot Start 

1s/

–130 dBm (GPS signal powers off 1s) 

Sensitivity 

Cold start 

–144 dBm 

Tracking 

–159 dBm 

 

 

1. 

The test values are the average of some test samples. 

2. 

If GPS and LTE Band 13 of ME936 are enabled at the same time, the GPS performance 
may be affected and the module may not be positioned in the weak signals. 

 

4.4.2 

Conducted Transmit Power 

The conducted transmit power is another indicator that measures the performance of 
ME936. The conducted transmit power refers to the maximum power that the module 
tested at the antenna port can transmit. According to the 3GPP protocol, the required 
transmit power varies with the power class. 

Table 4-4 lists the required ranges of the conducted transmit power of ME936. The 
tested values listed in the Test Value column must range from the minimum power to 
the maximum power. 

Table 4-4  

ME936 conducted Tx power 

Item 

3GPP Protocol 
Claim (dBm) 

ME936 Test Value (dBm) 

Min. 

Typ. 

Max. 

GSM850 

GMSK (1Tx Slot) 

31 to 35 

31.5 

32.5 

33.5 

8PSK (1Tx Slot) 

24 to 30 

25 

26 

27 

GSM900 

GMSK (1Tx Slot) 

31 to 35 

31.5 

32.5 

33.5 

8PSK (1Tx Slot) 

24 to 30 

25 

26 

27 

GSM1800 

GMSK (1Tx Slot) 

28 to 32 

28.5 

29.5 

30.5 

8PSK (1Tx Slot) 

23 to 29 

24 

25 

26 

GSM1900 

GMSK (1Tx Slot) 

28 to 32 

28.5 

29.5 

30.5 

8PSK (1Tx Slot) 

23 to 29 

24 

25 

26 

UMTS Band 1 

21 to 25 

22.5 

23.5 

24.5 

UMTS Band 2 

21 to 25 

22.5 

23.5 

24.5 

UMTS Band 4 

21 to 25 

22.5 

23.5 

24.5 

Summary of Contents for ME936


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands