Huawei ME909s Series Hardware Manual Download Page 67 | Manualshive

Page: 67 / 76

background image

HUAWEI ME909s Series LTE Mini PCIe Module
Hardware Guide

Mechanical Specifications

Issue 02 (2016-09-07)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

67

3. Place the plug cable assembly (held in the tool) over the corresponding

receptacle.

4. Assure that the plug and receptacle are aligned press-down perpendicular to the

mounting surface until both connectors are fully mated.

5. Remove the mating tool by pulling it up carefully.

Figure 6-5

Unmating the plug



The extraction tool is recommended.



Any attempt of unmating by pulling on the cable may result in damage and influence the
mechanical/electrical performance.

It is recommended not to apply any pull forces after the bending of the cable, as
described in Figure 6-6 .

Figure 6-6

Do not apply any pull forces after the bending of the cable

6.6 Thermal Design Guide

When using in the network, the ME909s Mini PCIe module (Mini PCIe) has high power
consumption. To improve the module reliability and stability, focus on the thermal
design of the device to speed up heat dissipation.

Take the following heat dissipation measures:



Do not hollow out the customer PCB.



Attach the thermal conductive material between the Mini PCIe and the customer
PCB. The recommended thermal conductivity of the thermal conductive material
is 1.0 W/m-k or higher (recommended manufacturers: Laird and Bergquist). The

«
...
65
66
67
68
69
...
»

Summary of Contents for ME909s Series













































































Reviews:

No comments

Related manuals for ME909s Series

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: Eaton Pages: 6

Brand: Bard Pages: 8

Brand: Bardiani Valvole Pages: 35

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: Olsberg Pages: 68

traxon e:cue LCE-mx

Brand: Osram Pages: 35

Brand: Linear Technology Pages: 7

J1000 CIMR-JC series

Brand: YASKAWA Pages: 25

Brand: Yolink Pages: 23

Brand: Velux Pages: 11

Brand: Kantronics Pages: 201

M-DUINO PLUS series

Brand: Industrial Shields Pages: 46

Hydropan-Single

Brand: ETNA Pages: 12

Brand: Broadcast Tools Pages: 39

TOP-43 EE Series

Brand: CAME Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands