Huawei LampSite Page 68 Installation Manual Download

Page: 68 / 100

Step 5

Fit the four hooks of the pRRU into the installation kits, as shown in

Figure 5-15

. If the hooks

are properly installed, a slight clack can be heard.

NOTE

It is recommended that you observe the installation from one side of the pRRU when inserting hooks into
the kits.

Figure 5-15

Installing a pRRU

----End

5.4.4 pRRU Installed on a Pole

A pRRU can be installed on a metal pole indoors.

Procedure

Step 1

Determine the position for installing the pRRU based on the construction blueprint and the space
requirements.

NOTE

For pRRU installation space requirements, see

5.1.3 Space Requirements

Step 2

If the diameter of the pole ranges from 30 mm to 70 mm, use the delivered V clamp, installation
plate, and bolts to install the pRRU on the pole. Lead the M6x80 bolt through the plate, and
tighten the bolt to a torque of 5 N•m, as shown in

Figure 5-16

LampSite
Installation Guide

5 Installing a pRRU

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Summary of Contents for LampSite





































































































Search results

Summary of Contents for LampSite

Reviews:

Related manuals for LampSite

Brands by name

Popular brands

Huawei LampSite, Installation Manual

Search results

Summary of Contents for LampSite

Reviews:

Related manuals for LampSite

Brands by name

Popular brands