Huawei IPC6221-VRZ-SP Configuration Manual Download Page 65

Page: 65 / 126

Set SNMP parameters based on the site requirements.

7.6.1 Set SNMP v1/v2c parameters

When SNMP v1 or SNMP v2c is used, the NMS visits the IPC using a community name with
the read-only or read-write right.

Context

Two sets of interaction parameters have been set by default. You can use the default settings,
or click

Modify

Delete

to modify or delete them. When SNMP v1 or SNMP v2c is used,

you can set a maximum of three sets of interaction parameters. This section mainly describes
how to add a set of interaction parameters.

Procedure

Step 1

Choose

Settings

Network Configuration

SNMP Parameters

The

SNMP Parameters

page is displayed, as shown in

Figure 7-9

SNMP Parameters page

Step 2

Click

Add

in the

SNMP v1/v2c Parameters

area.

The page for setting interaction parameters is displayed, as shown in

Figure 7-10

Setting SNMP v1/v2c parameters

Step 3

Set

Community name

Confirm name

and

Community property

When

Community property

is set to

Readonly

, you can only view IPC configurations on the

NMS.

When

Community property

is set to

Read&Write

, you can view and modify IPC

configurations on the NMS.

Step 4

Click

The

SNMP Parameters

page is displayed.

IPC6221-VRZ-SP
Configuration Guide

7 Setting Network Parameters

Issue 02 (2016-04-06)

Huawei Proprietary and Confidential

Summary of Contents for IPC6221-VRZ-SP































































































































Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands

Huawei IPC6221-VRZ-SP, Configuration Manual

Search results

Summary of Contents for IPC6221-VRZ-SP

Reviews:

Related manuals for IPC6221-VRZ-SP

Brands by name

Popular brands